เวลาทำการ: จันทร์-ศุกร์ เวลา 09:00-17:30 น.

!!   รู้ลึก  รู้จริง เรื่องเครื่องมือทดสอบวัสดุ  !  ยืน 1 เรื่องมาตรฐานการให้บริการ   

ภาษา :

สนใจสินค้าและบริการ โปรดติดต่อ Line : @siamintercorp

เครื่องอัดขึ้นรูปยางและพลาสติก (For use with frac sand, resin coated sand and ceramic proppant) ยี่ห้อ Carver (SIT55) เครื่องอัดขึ้นรูปยางและพลาสติก (For use with frac sand, resin coated sand and ceramic proppant) ยี่ห้อ Carver (SIT55)
หมวดหมู่สินค้า: Proppant Crush Test Press
*ราคาอาจมีการเปลี่ยนแปลงตามอัตราแลกเปลี่ยน โปรดสอบถาม Line : @siamintercorp

08 มกราคม 2567

ผู้ชม 1478 ผู้ชม


Model CMG28-12-PCR  
  • Compatible with ISO 13503-2:2006
  • For use with frac sand, resin coated sand and ceramic proppant

Carver Inc. is proud to introduce Model CMG28-12-PCR proppant Crush Test press. This Monarch Series press meets the critical demands of ISO 13503-2:2006 with unsurpassed cycle repeatability. The proportional hydraulic system is capable of applying a constant rate of 13.8 MPa/min. (2000 PSI min.) from 2 ton to 28 ton clamp force within a ±2.5% deviation. The operator interface allows easy setup of press control parameters and includes ample recipe storage.

 
Specifications of Model CM28-12-PCR Proppant Crush Test Press:  
  • Compression force: 2-28 ton
  • Minimum 1,275 psi on a 2" diameter crush die
  • Maximum 17,800 psi on a 2" diameter crush die
  • Hardened plates: 12” L-R x 12” F-B fully guided platens to ensure parallelism
  • Positive stop on platens for centering the crush die
  • Open daylight: 6”-12”
  • Cylinder stroke: 6”
  • Self-contained hydraulic system
  • Available with and without 2” ID crush die (compatible with ISO 13503-2)
  • “Mini” ViewPoint control system including:
  • Allen Bradley programmable controller
  • PanelView Touch screen interface
  • Closed-loop control of clamp pressure
  • Real time graphical display of process parameters
  • Recipe storage (up to 30 recipes of 24 segments)
  • Two hand close buttons
  • Polycarbonate safety guards around the clamp area with manual sliding interlocked operator gate
  • Dimensions: 46” w x 35” d x 74” h
  • Weight: 1,900 lbs
 
Model CMG40-12-PCR  
  • Compatible with ISO 13503-2:2006
  • For use with frac sand, resin coated sand and ceramic proppant

Carver Inc. is proud to introduce Model CMG40-12-PCR proppant Crush Test press. This Monarch Series press meets the critical demands of ISO 13503-2:2006 with unsurpassed cycle repeatability. The proportional hydraulic system is capable of applying a constant rate of 13.8 MPa/min. (2000 PSI min.) from 2 ton to 40 ton clamp force within a ±2.5% deviation. The operator interface allows easy setup of press control parameters and includes ample recipe storage.

 
Specifications of Model CM40-12-PCR Proppant Crush Test Press:  
  • Compression force: 2-40 ton
  • Minimum 1,275 psi on a 2" diameter crush die
  • Maximum 25,000 psi on a 2" diameter crush die
  • Hardened plates: 12” L-R x 12” F-B fully guided platens to ensure parallelism
  • Positive stop on platens for centering the crush die
  • Open daylight: 6”-12”
  • Cylinder stroke: 6”
  • Self-contained hydraulic system
  • Available with and without 2” ID crush die (compatible with ISO 13503-2)
  • “Mini” ViewPoint control system including:
  • Allen Bradley programmable controller
  • PanelView Touch screen interface
  • Closed-loop control of clamp pressure
  • Real time graphical display of process parameters
  • Recipe storage (up to 30 recipes of 24 segments)
  • Two hand close buttons
  • Polycarbonate safety guards around the clamp area with manual sliding interlocked operator gate
  • Dimensions: 46” w x 35” d x 74” h
  • Weight: 2,400 lbs
 PDF Brochure [ Last Update 2021 ]
ขอใบเสนอราคา
Reference Customer (กดที่โลโก้ เพื่อดูเว็บไซต์ของลูกค้าที่สั่งซื้อสินค้ากับทางบริษัท)​
อยู่ในระหว่างอัพเดทข้อมูล...        
Engine by shopup.com